[. . . ] HP Color LaserJet CM1015/CM1017 MFP User Guide HP Color LaserJet CM1015/CM1017 MFP User Guide Copyright and License © 2006 Copyright Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. [. . . ] After selecting the IP address, enter the subnet mask and default gateway by repeating steps 8­ 10. To get subnet mask and default gateway information in Windows XP Pro: 1. If at any time during the configuration Cancel is pressed, the system exits the menu and the addresses are not saved. Press the navigation arrows to select TCP/IP configuration, then press OK. It can take several minutes before the automatic IP address is ready for use. NOTE To disable or enable specific automatic IP modes (such as BOOTP, DHCP, or AutoIP), use options provided in the embedded Web server or HP ToolboxFX only. Link speed settings NOTE Incorrect changes to the link speed and duplex settings might prevent the MFP from communicating with other network devices. Also note that changes may cause the MFP to power cycle; makes changes only while the MFP is idle. Automatic 10T Full 10T Half 100T Full 100T Half ENWW Set up the MFP and use it on the network 103 NOTE The setting must match with the network device to which you are connecting (a network hub, switch, gateway, or computer). The MFP may power cycle. Supported network protocols This table lists the networking services/protocols supported on the HP Color LaserJet CM1017 MFP. Table 11-1 Printing Service name port9100 (Direct Mode) Line printer daemon (LPD) Description Printing service Printing service Table 11-2 Network device discovery Service name SLP (Service Location Protocol) Description Device Discovery Protocol, used to help find and configure network devices. Device Discovery Protocol, used to help find and configure network devices. For more information, see Software for Macintosh. Bonjour, (commonly referred to as Rendezvous or mDNS (multicast Domain Name Service)) Table 11-3 Messaging and management Service name HTTP (Hyper Text Transfer Protocol) SNMP (Simple Network Management Protocol) Description Allows web browsers to communicate with embedded Web server. SNMP v1 and standard MIB-II (Management Information Base) objects are supported. Table 11-4 IP addressing Service name DHCP (Dynamic Host Configuration Protocol) Description For Automatic IP address assignment. Generally requires no user intervention for MFP to obtain IP address from a DHCP server. Requires administrator to input devices MAC hardware address on BOOTP server in order for MFP to obtain an IP address from that server. If neither a DHCP server nor a BOOTP server is present, this service allows the BOOTP (Bootstrap Protocol) Auto IP 104 Chapter 11 Network Setup and Administration (HP Color LaserJet CM1017 MFP) ENWW Table 11-4 IP addressing (continued) Service name Description MFP to generate a unique IP address. For example, the IP address 169. 254. 0. 10 represents a series of triplets ranging from 0 to 254; this address is not manually configurable. TCP/IP TCP/IP (Transmission Control Protocol/Internet Protocol) is a suite of protocols designed to define the way computers and other devices communicate with each other over a network. TCP/IP is rapidly becoming the most used set of protocols because the Internet is based on TCP/IP. If there is a network that you want to connect to the Internet, use TCP/IP to communicate. NOTE This MFP does not support IP V6. Internet Protocol (IP) When information is sent across the network, the data is broken down into small packets. Each packet is encoded with IP information, such as the IP address of the sender and receiver. IP packets can be routed over routers and gateways, devices that connect a network with other networks. When IP packets are sent, there is no guarantee that they arrive at their destination in the proper sequence. [. . . ] 1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems. Operation is subject to the following two Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name or the product number(s). [. . . ]